Header Ads

How to Use Aspire Puxos Vape Mod - User Manual

Specifications


Wattage range: 1-100W/1-80W
Output Voltage: 0.1-8.4V
Resistance Parameters: 0.1-3.5ohms
Continuous Fire Time can be adjusted from 5s to 15s Charging Port: Micro-USB charging port
Screen: 0.96 inch OLED screen
Firmware updateable: N/A
Dimensions: 85*41*27mm
Battery type: Compatible with 18650/21700 and 20700 high rate
discharge batteries
Temperature Control
Temperature Range (F):200-600F
Temperature Range (C):100-315℃


Protection Features


Automatic Cut Off
Short Circuit Protection
Low Resistance Protection
Overheat Protection
Over Charge Protection
Over Discharge Protection

 Aspire Puxos Instructions


1. The mod will automatically turn on after installing battery, the screen will then display “18650” and “21700” choose the correct value according to the battery inserted, choose “18650” battery, the maximum output wattage of the mod is 80W, choose “21700” battery the maximum output wattage is 100W.

NB: (1) when using an 18650 battery, it must be mounted in the supplied adapter.

2.  When using a 20700 battery, select the same output as 21700 battery.
Press the fire button 5 times within 2 seconds to either lock or unlock the device. While the mod is locked, press the fire button for 3 seconds to turn the system off. To turn the mod back on, press the fire button 5 times rapidly.

3. Pressing fire button and down button simultaneously for 0.5 second to either lock or unlock keys, which is indicated by a lock symbol on the screen. While the keys are in locked mode, wattage or temperature settings cannot be adjusted but fire button still functions.

4. Pressing fire button and up button simultaneously for 0.5 second will allow you to select between Wattage, Voltage, Bypass, CPS
(C1/C2/C3), TC(Ni/Ti/SS316L) and TCR(M1/M2/M3). Press up or down button to select modes, press fire button to select/confirm.

5. In wattage mode, the mod also allows you to adjust the strength settings, “H” indicates hard, “N” means Normal, “S” means soft.

6. TCR settings: While the mod is in TC mode, pressing up and down buttons simultaneously to enter or exit PWR and TCR settings. Pressing fire button to select between PWR and TCR, up and down button to change numbers, PWR numbers can be adjusted from 1W to 80/100W, while TCR range is from 0.10 to 9.99. (Note: TCR numbers for TC(Ni/Ti/SS316L) cannot be adjusted.)

7. When the mod is in CPS (Customizable Power Settings), pressing up and down buttons simultaneously will allow you to fine-tune your heat ramp-up (power curve). Press up or down button to change wattage, press fire button to select time from 1 to 10 seconds, pressing up and down buttons simultaneously again will exit your Customizable Power Settings.

8. While the mod is in TC mode attaching a new atomizer the mod will ead “New Atomizer?” followed by “YES+/NO-”. Select “YES+” and the mod will read the original coil resistance. Select “NO“and the mod will keep its previous coil resistance settings. (Note: To ensure accuracy, when first installing a new atomizer, make sure the screen is lit and the coil attached is at room temperature before attaching it to the mod.)

9. When the mod is on, press the fire button 3 times quickly to put the mod into or out of stealth mode, while in stealth mode the mod can still     fire but the wattage or temperature settings cannot be adjusted.

10. Pressing the up and down buttons simultaneously for 2 seconds will allow you to adjust the screen brightness or manually rotate the screen, press up /down button to select between Brightness and Flip screen, press fire button to enter, when in screen brightness settings, press up/down button to adjust the brightness, press fire button to save and exit.


Charging


Charging the Puxos via Micro-USB charging port, the maximum current can reach up to 2A.
Connect the mod to the charger and the screen will display a growing battery icon and the battery percentage. When the battery charge reaches 4.2V or is fully charged, the mod will stop charging and the screen will remain off.

The batteries cannot be replaced while charging. Please unplug the USB cable before changing your batteries.

When the battery charge drops below 1.5V or battery incorrectly installed the mod will stop charging.
When the mod detects the USB charge voltage is less than 4.3V or above 5.5V, it will stop charging and the screen will display “CHECK CHARGER”.
To accomplish 2A charge current, the adaptor output should be 5V/2A.


Battery installation



1. Remove both the side panels.
2. Remove the battery by pushing finger through the hole in one side.
3. Replace with fresh battery.
4. Replace both side covers.

No comments

Powered by Blogger.